中文简体
English
Material & Specification Overview
The table below summarizes the profile characteristics most relevant to countertop applications. Exact dimensions depend on the specific panel size selected - please confirm against the datasheet for your chosen profile and share your grill or heat source clearance distance for a suitability check.
| Item | Detail |
| Recommended Structure | Solid core composite with a co-extrusion capped surface |
| Standard Panel Thickness | 20mm - 30mm, depending on required rigidity for an unsupported countertop span |
| Standard Panel Width | 150mm - 300mm, or wider custom panel sizes for a continuous countertop look |
| Heat Exposure Consideration | Recommended minimum clearance from direct grill heat should follow the grill manufacturer's own clearance guidance in addition to our material's general heat tolerance |
| Surface Finish Options | Matte or semi-gloss capped finish, wood-grain embossed capped finish |
| Edge Detail | Square edge or rounded bullnose edge trim available for the visible countertop front edge |
Product Photography
We provide installed outdoor kitchen project photos showing the panel in context around a grill or sink area, alongside standard board shots, surface texture close-ups, a cross-section cut, and export packaging photos, since seeing the material used as a countertop specifically - rather than as a deck or wall panel - is usually the most useful reference point for buyers evaluating this application.
A note on unsupported spans: countertops sometimes need to span an open area, such as above a beverage fridge or storage cabinet, without continuous support underneath; let us know your typical unsupported span length and we can recommend an appropriate thickness or an internal support batten approach to avoid noticeable flex or sag over time.
Minimum Order Quantity & Pricing Structure
Countertop panel orders are often smaller in total volume than a full decking or cladding project, since a single outdoor kitchen typically needs only a few linear meters of countertop surface, so we try to accommodate smaller trial quantities for this application more readily than for our bulk decking lines. MOQ for a first trial order is typically 1 x 20ft container, though for fabricators and patio contractors ordering repeatedly across many smaller residential projects, we can also discuss a standing supply arrangement with smaller, more frequent shipments rather than one large upfront order.
| Order Volume | Pricing Tier |
| Sample pieces | Sample fee + courier, often credited toward first order |
| 1 x 20ft container | Standard FOB pricing (based on capped solid core specification) |
| 1 x 40ft HQ container | Discounted per-sqm pricing |
| Repeat fabricator/contractor volumes | Negotiated pricing with smaller, more frequent shipment scheduling |
Quotations are typically given as FOB Ningbo or Shanghai, with CIF and DDP available once destination and Incoterm are confirmed. Standard payment terms are 30% deposit by T/T with balance against the B/L copy; smaller fabricators new to importing can also discuss a slightly adjusted deposit structure for a modest first trial order.
Because countertop panels are often specified alongside a matching decking or cladding order for the same outdoor living space project, we can also prepare a single combined quotation covering both product types, which is generally more convenient for your internal approval and avoids the shipping inefficiency of two entirely separate smaller orders.
OEM & Customization Options
Because countertop panels are a highly visible, close-contact surface, customization conversations here focus heavily on getting the exact color, edge detail, and panel width right for a cohesive outdoor kitchen design.
- Color matching - match the countertop to an existing decking or cladding color already used elsewhere in the outdoor living space, or to a client's kitchen design scheme
- Edge profile - square edge for a modern look, or a rounded bullnose edge for a softer, more traditional countertop feel
- Panel width - wider custom panel widths can be developed for continuous countertop runs that would otherwise need visible seams with our standard board widths
- Cutout allowances - we can advise on recommended clearance and edge-sealing practices around sink or cooktop cutouts, which your fabricator will typically cut on-site
- Branding - private label packaging for outdoor kitchen fabricators or hospitality developers ordering across multiple projects
For fabricators developing a signature outdoor kitchen product line, we can also discuss developing a dedicated panel width and edge profile exclusive to your business, subject to a reasonable minimum order commitment for the new tooling.
We can also supply small offcut or sample pieces specifically sized for testing cutout and edge-routing techniques before your fabrication team works on the actual project panels, which many fabricators find useful when handling this material for the first time and wanting to practice their cutting technique on a low-stakes test piece first.
We can also share cutting speed and blade-type recommendations that other fabricators have found effective with this material, since the right tooling choice makes a noticeable difference in edge finish quality on a visible countertop application.
Certification & Quality Control
Because this application involves food contact surfaces and proximity to cooking heat, buyers sourcing for outdoor kitchens typically ask more specific questions about heat tolerance and surface hygiene than for standard decking or cladding.
| Certification / Test | Availability |
| REACH / RoHS compliance | Standard formulation compliant |
| Third-party lab reports | Water absorption, surface hardness, and general heat tolerance test data available on request (SGS/BV) |
| Surface cleanability | Capped surface designed to resist staining from common food and beverage contact; not marketed as a certified food-contact material in the way a dedicated kitchen countertop material would be |
| Factory quality system | ISO 9001 factory management system |
Our QC process for countertop panels includes standard raw material inspection, dimensional monitoring, and pre-shipment sampling, with particular attention to surface finish consistency and edge-trim fit, since visible surface defects matter more on a close-contact countertop than on a floor or wall panel viewed from a greater distance. We recommend that fabricators apply a food-safe sealant appropriate to their local regulations if the panel will have direct, prolonged food contact, and we are glad to discuss this consideration further if it applies to your project.
We also recommend that fabricators avoid placing the panel in direct, sustained contact with a hot pan or dish removed straight from an open flame, similar to the general care guidance given for most solid-surface or engineered countertop materials, and we can share a simple care and use guide that fabricators often pass along to their end clients after installation.
Production Capacity & Lead Time
Countertop panel orders generally follow the production schedule of our co-extrusion capped solid core line, with lead time depending on whether a standard width and color are selected or a custom panel dimension is required.
| Item | Detail |
| Monthly capacity | Follows our capped solid core composite line capacity, scheduled alongside other capped-surface orders |
| Sample lead time | 5-8 working days for existing panel widths and colors |
| Standard order lead time | 20-30 days after deposit and specification confirmation |
| Custom panel width lead time | Additional 25-35 days for new tooling if a wider continuous panel is required |
| Small-order note | For fabricators placing smaller, more frequent orders, we recommend confirming an approximate ordering rhythm with us so we can better plan production slot allocation across your recurring smaller shipments |
We provide production progress updates and can share close-up photos of the finished panel surface and edge detail before your order is packed and shipped.
Because countertop orders are frequently smaller and more time-sensitive relative to a homeowner's overall renovation schedule, we try to keep communication tight on expected ship dates for this line specifically, giving your project's confirmed timeline the buffer it needs rather than waiting for you to follow up and ask.
If your project has a hard installation deadline tied to a client's event or opening date, please flag this clearly at the time of order so we can confirm feasibility honestly before your deposit is paid, rather than after production has already begun, since an honest early answer is always more useful than an optimistic one given later.
Logistics & After-Sales Support
Countertop panel shipments are often smaller and more frequent than a bulk decking order, so our logistics approach for this line focuses on keeping smaller shipments cost-efficient rather than only optimizing for full-container volume.
- Shipping ports - orders typically go out via Ningbo or Shanghai port; FOB, CIF, or DDP quoting available, including LCL (less-than-container-load) options for smaller countertop-only orders
- Transit packaging - individually protected panels with edge and corner protection, given the close-contact visual scrutiny this product receives once installed
- Documentation - commercial invoice, packing list, bill of lading, and certificate of origin provided as standard
- Damage/shortage claims - please document any panel or edge damage with photos at unloading before installation begins; verified manufacturing defects are resolved through replacement stock or credit on the next order
- Installation guidance - fabrication guidance covering recommended support spacing, cutout clearance, and edge-sealing practices is provided for your fabrication team
For fabricators who order smaller quantities regularly, we can also discuss consolidating multiple smaller orders into a single shared container shipment to help keep per-unit freight cost reasonable.
Because this panel is often the visible centerpiece of an outdoor kitchen, we recommend inspecting panels for surface or edge damage immediately upon unloading and before any fabrication cutting begins, since it is far easier for us to replace a damaged panel before it has been cut to a custom size than after fabrication work has already started.
Our export team can also advise your freight forwarder on the best pallet orientation for unloading with typical residential or small-jobsite equipment, since countertop panel deliveries sometimes go to a fabrication workshop rather than a large commercial site with heavy unloading equipment on hand.
Frequently Asked Questions
Q: Can this material be placed directly next to a built-in grill?
A: A reasonable clearance from the grill's direct heat radius is recommended, generally following the grill manufacturer's own clearance guidance; we can advise further once you share your specific grill model and layout.
Q: Is this countertop material food-safe?
A: The capped surface resists staining from typical food and beverage contact, though we recommend checking your local food-safety regulations and applying an appropriate sealant if the surface will have direct, prolonged food preparation contact.
Q: Can the countertop match my existing composite decking color?
A: In most cases, yes - if you tell us the decking product and color you are using, we can confirm whether a matching countertop panel color is already available or would need a color-matching sample.
Q: How is a sink or cooktop cutout handled?
A: Cutouts are typically made on-site by your fabricator using standard tools for composite material, with edge sealing recommended around the cut opening; we can provide general cutout and sealing guidance to share with your fabrication team.
Q: Can I order a small trial quantity before committing to a full outdoor kitchen project?
A: Yes, we understand countertop orders are often smaller than a full decking project, and we are glad to work with a modest trial quantity for fabricators testing this material for the first time.
Q: Does the panel need to be sealed after cutting a cutout on-site?
A: Yes, we recommend sealing any freshly cut edge, such as around a sink or cooktop opening, to maintain the surface's moisture resistance at that exposed cut edge, and can advise on a suitable edge-sealing product compatible with the capped surface.
